Hadco Light Emitting Diode LED Landscaping Lights

RSC2 Louver Steplyte
Line Voltage LED Landscape Step and Deck Lighting

Hadco RSC2 Louver Steplyte or Bricklyte
Line Voltage Landscape Step and Deck Lighting

RSC2AK5D3E Louver Steplight with 3 LEDs
RSC2AL5D5E Louver Steplight with 5 LEDs

Select Finish: A Black. B White. H Bronze or N Natural Brass
Select Optics: K5 Symmetric Optics or L5 Symmetric Optics
Select Wattage: D3 3 x 1W LEDs or D5 5 x 1W LEDs

Height: 3 1/2" (90mm)
Width: 9" (229mm)
Depth: 3 1/2" (90mm)
Max. Weight: 3.64 lb.

Hadco RSC2

Fasteners are 300 series stainless steel. Gasketing is silicone. Recessed housing contains four (4) 1/2 " NPS conduit inlets (two (2) on bottom and one on each side) and internal pull-through wiring compartment. Die-cast aluminum trim ring contains less than 0.3% copper to resist corrosion. Cast bronze fixture has polycarbonate, color impregnated, dark bronze finish. Die-cast copper-free aluminum with 45° cutoff, with frosted tempered glass. Cast bronze louver is natural cast bronze with frosted tempered glass. Die-cast aluminum back box contains less than 0.3% copper to prevent corrosion in concrete or masonry applications. Integral and furnished as standard on all fixtures. This enables fixture to be used in accordance with NEC Article 680-51 in installations without an external low-water cutoff.

Finish: Zinc-rich primer and thermoset powdercoat for durability. Thermoset polyester powdercoat is electrostatically applied after a five-stage conversion cleaning process and bonded by heat fusion thermosetting. Laboratory tested for superior weatherability and fade resistance in accordance with ASTM B-117-64 and ANSI/ASTM G53-77 specifications.

Optical Assembly: The cast louver offers lower light levels with cut-off for lighting stairways or general lighting where shielding of the light source is more important than high light levels. Reflector is formed from highly reflective aluminum. Symmetric.

Lamping: Type 3 Luxeon® high-output LEDs powered at 700mA to operate for 50,000 hours.
Electrical Assembly: Electronic 120 volt AC to 12 volt regulated DC, power supply.

Warranty: Three-year limited warranty.
Certification: UL Listed to U.S. safety standards for wet locations. cUL Listed to Canadian safety standards for wet locations. Manufactured to ISO 9001:2000 Standards. ADA Compliant when used in indoor and outdoor wall applications.
IP Rating: IP66: Dust-tight and sealed against direct jets of water.

RSF2 Flat Opal Lens Steplyte or Bricklyte
Line Voltage LED Landscape Step and Deck Lighting

Hadco RSF2 Flat Opal Lens Steplyte or Bricklyte
Line Voltage Landscape Step and Deck Lighting

RSF2AL5D3E Flat Opal Lens Steplight with 3 LEDs
RSF2AL5D5E Flat Opal Lens Steplight with 5 LEDs

Select Finish: A Black or H Bronze
Optics: L5 Symmetric Optics only
Select Wattage: D3 3 x 1W LEDs or D5 5 x 1W LEDs

Height: 3 1/2" (90mm)
Width: 9" (229mm)
Depth: 3 1/2" (90mm)
Max. Weight: 3.65 lb.

Hadco RSF2

Die-cast aluminum trim ring contains less than 0.3% copper to resist corrosion. Cast bronze fixture has polycarbonate, color impregnated, dark bronze finish. Die-cast aluminum back box contains less than 0.3% copper to prevent corrosion in concrete or masonry applications.

Finish: Zinc-rich primer and thermoset powdercoat for durability.

Optical Assembly: Opal Lens - made of UV stabilized injection molded polycarbonate. Specular aluminum formed reflector.

Lamping: Type 1 Luxeon® high-output LEDs powered at 350mA to operate for 50,000 hours. Electrical Assembly: Supply wires connect directly to the quick connect on the integral power supply. Electronic 120 volt AC to 12 volt regulated DC, power supply.

Warranty: Three-year limited warranty.
Certification: UL Listed to U.S. safety standards for wet locations. cUL Listed to Canadian safety standards for wet locations. Manufactured to ISO 9001:2000 Standards. ADA Compliant when used in indoor and outdoor wall applications.
IP Rating: IP66: Dust-tight and sealed against direct jets of water.

RSS2 Internal Louver Steplight or Bricklyte
Line Voltage LED Landscape Step and Deck Lighting

Hadco RSS2 Internal Louver Steplyte or Bricklyte
Line Voltage Landscape Step and Deck Lighting

RSS2AK5D3E Internal Louver Steplyte with 3 LEDs
RSS2AK5D5E Internal Louver Steplyte with 5 LEDs

Select Finish: A Black or H Bronze
Optics: K5 Symmetric Optics only
Select Wattage: D3 3 x 1W LEDs or D5 5 x 1W LEDs

Height: 3 1/2" (90mm)
Width: 9" (229mm)
Depth: 3 1/2" (90mm)
Max. Weight: 3.75 lb.

Hadco RSS2

Die-cast aluminum back box contains less than 0.3% copper to prevent corrosion in concrete or masonry applications. Gasketing is silicone. Fasteners are 300 series stainless steel. Note: Recessed housing contains four (4) 1/2 " NPS conduit inlets (two (2) on bottom and one on each side) and internal pull-through wiring compartment. Die-cast aluminum trim ring contains less than 0.3% copper to resist corrosion. Clear UV stabilized injection molded polycarbonate with 45° louvered screen insert.

Finish: Zinc-rich primer and thermoset powdercoat for durability.

Optical Assembly: The cast louver offers lower light levels with cut-off for lighting stairways or general lighting where shielding of the light source is more important than high light levels. Specular aluminum formed reflector.

Lamping: 13W CFL (GX23D-2). Type 1 Luxeon® high-output LEDs powered at 350mA to operate for 50,000 hours. 40W maximum T10 lamps. Lower wattage lamps are acceptable.
Electrical Assembly: 4kv rated medium base porcelain socket. Nickel-plated screw shell with center contact. Electronic 120 volt AC to 12 volt regulated DC, power supply.
Ballast: Core and coil, NPF, 0° starting temperature.

Warranty: Three-year limited warranty.
Certification: UL Listed to U.S. safety standards for wet locations. cUL Listed to Canadian safety standards for wet locations. Manufactured to ISO 9001:2000 Standards. ADA Compliant when used in indoor and outdoor wall applications.
IP Rating: IP66: Dust-tight and sealed against direct jets of water.

RSV2 Vertical Louver Steplight or Bricklyte
Line Voltage LED Landscape Step and Deck Lighting

Hadco RSV2 Vertical Louver Steplight or Bricklyte
Line Voltage Landscape Step and Deck Lighting

RSV2AK5D3E Vertical Louver Steplight with 3 LEDs
RSV2AK5D5E Vertical Louver Steplight with 5 LEDs

Select Finish: A Black. B White. H Bronze or N Natural Brass
Select Optics: K5 Symmetric Optics only
Select Wattage: D3 3 x 1W LEDs or D5 5 x 1W LEDs

Height: 8 3/4" (222mm)
Width: 3 1/4" (83mm)
Depth: 3 1/2" (90mm)
Max. Weight: 3.6 lb.

Hadco RSV2

Recessed housing contains four (4) 1/2 " NPS conduit inlets (two (2) on bottom and one on each side) and internal pull-through wiring compartment. Die-cast aluminum back box contains less than 0.3% copper to prevent corrosion in concrete or masonry applications. Fasteners are 300 series stainless steel. Die-cast aluminum trim ring contains less than 0.3% copper to resist corrosion. Cast bronze fixture has polycarbonate, color impregnated, dark bronze finish. Die-cast copper-free aluminum with 45° cutoff, with frosted tempered glass. Cast bronze louver is natural cast bronze with frosted tempered glass. Gasketing is silicone.

Finish: Zinc-rich primer and thermoset powdercoat for durability.

Optical Assembly: Specular aluminum formed reflector.

Lamping: 13W CFL (GX23D-2). Lower wattage lamps are acceptable. 40W maximum T10 lamps. Type 1 Luxeon® high-output LEDs powered at 350mA to operate for 50,000 hours.
Electrical Assembly: Electronic 120 volt AC to 12 volt regulated DC, power supply. Single contact bayonet (S-8). 13W Fluorescent Socket is a GX23/GX23-2. 4kv rated medium base porcelain socket. Nickel-plated screw shell with center contact. Fixture is 12 vo Light Internal electronic transformer has 120 volt input. Pre-wired with high temperature 18 AWG wire.
Ballast: Core and coil, NPF, 0° starting temperature.

Warranty: Three-year limited warranty.
Certification: UL Listed to U.S. safety standards for wet locations. cUL Listed to Canadian safety standards for wet locations. Manufactured to ISO 9001:2000 Standards. ADA Compliant when used in indoor and outdoor wall applications.
IP Rating: IP66: Dust-tight and sealed against direct jets of water.

LED Housing Only LED Housing Only (RS2D-_HO)

Hadco RS2D-_HO LED Housing Only for Steplight or Bricklyte

RS2D-AHO LED Housing Only for Pre-Shipment, A Black
RS2D-BHO LED Housing Only for Pre-Shipment, B White
RS2D-HHO LED Housing Only for Pre-Shipment, H Bronze
RS2D-NHO LED Housing Only for Pre-Shipment, N Natural Brass

LED housing only. When housing only is ordered for pre-shipment, add suffix "LH" (Less Housing) to complete catalog number to fixture without housing.

Select Finish: A Black. B White. H Bronze or N Natural Brass

LED Underwater Light (ULW5D4)
Specialty Low Voltage Landscape Light

Hadco LED Underwater Light (ULW5D4) LED Pond Light
Specialty Low Voltage Landscape Light

ULW5D4-H LED Ultem Underwater

Finish: H Bronze only

Height: 6 11/16" (170mm)
Width: 4 1/16" (103mm)
Max. Weight: 5.04 lb.

Hadco ULW5D4

One-piece injection molded ULTEM® High Performance Polymer composite. Lens ring is a Single-piece injection molded ULTEM® High Performance Polymer with gasketed lens. Twist-off operation for ease of maintenance. Fasteners are 300 series stainless steel.

Finish: Composite is textured, pressure formed, molded-in-color.

Optical Assembly: Integral collimating flood (25°) optics. Clear convex lens, high temperature glass furnished with silicone O-ring for watertight seal.

H= Bronze

Lamping: Type 3 Luxeon® high-output LEDs powered at 700mA to operate for 50,000 hours.
Electrical Assembly: Input voltage range (VAC): 10.8 - 17.5. Input frequency: 60Hz. Integral surge protector built into LED driver circuit. 12 volts, 12.4 total watts. Standard 10 ft. 16-3 AWG, 105° C, STOW water-resistant cord. Fixture is pre-wired and potted to prevent water entry. 12 Volt system requires remote transformer, not included.

Warranty: Three-year limited warranty.
Certification: UL Listed to U.S. safety standards for wet locations. cUL Listed to Canadian safety standards for wet locations. Manufactured to ISO 9001:2000 Standards.
IP Rating: IP66/68 to 1M (3.28FT): Dust-tight and dual rated - sealed against direct jets of water and against continuous immersion up to a depth of 1 meter (3.28 feet).

Hadco LED Inground ILN5D4 & ILW5D4 Spot or Flood Landscape Lighting

ILN5D4-H LED Ultem Inground - Spot
ILW5D4-H LED Ultem Inground - Flood

Housing: One-piece injection molded ULTEM® High Performance Polymer composite. Lens ring is a Single-piece injection molded ULTEM® High Performance Polymer with gasketed lens. Twist-off operation for ease of maintenance. Fasteners are 300 series stainless steel.

Finish: Composite is textured, pressure formed, molded-in-color.

Height: 4 3/8" (111mm)
Width: 4 1/8" (105mm)
Max. Weight: 1.24 lb.

Hadco ILN5D4 & ILW5D4

Optical Assembly: Integral collimating flood (25°) optics. Clear convex lens, high temperature glass furnished with silicone O-ring for watertight seal.

Lamping: Type 3 Luxeon® high-output LEDs powered at 700mA to operate for 50,000 hours.

Electrical Assembly: Input voltage range (VAC): 10.8 - 17.5. Input frequency: 60Hz. Integral surge protector built into LED driver circuit. 12 volts, 12.4 total watts. 12 Volt fixture is pre-wired with 3-ft pigtail of 18-2 AWG, 105° C, SPT-1 wire. Low voltage quick connector, catalog #LVC3 included for easy hook-up to the low voltage supply cable, not included. 12 Volt system requires remote transformer, not included.

Warranty: Three-year limited warranty.

Certification: UL Listed to U.S. safety standards for wet locations. cUL Listed to Canadian safety standards for wet locations. Manufactured to ISO 9001:2000 Standards.

IP Rating: IP66/68 to 1M (3.28FT): Dust-tight and dual rated - sealed against direct jets of water and against continuous immersion up to a depth of 1 meter (3.28 feet).

Finish: H Bronze

H= Bronze

Hadco LED Bullyte BLN5D4 & BLW5D4 Spots & Flood Die-cast marine grade aluminum alloy bullet landscape lighting

BLN5D4-A LED Bullyte - Spot
BLN5D4-H LED Bullyte - Spot
BLW5D4-A LED Bullyte - Flood
BLW5D4-H LED Bullyte - Flood

Housing: Die-cast marine grade aluminum alloy. Fully rotatable shroud, double gasketed, die-cast marine grade alloy aluminum. Fully-adjustable swivel arm with vibration-proof locking teeth. 1/2 " NPS male threads to screw on to accessory mounting stake or junction box, sold separately. Fasteners are 300 series stainless steel. Gasketing is silicone.

Finish: Thermoset polyester powdercoat is electrostatically applied after a five-stage conversion cleaning process and bonded by heat fusion thermosetting. Laboratory tested for superior weatherability and fade resistance in accordance with ASTM B-117-64 and ANSI/ASTM G53-77 specifications.

Optical Assembly: Integral collimating flood (25°) optics. Clear tempered glass affixed at 10° angle for natural cleaning.

Lamping: Type 3 Luxeon® high-output LEDs powered at 700mA to operate for 50,000 hours.

Electrical Assembly: Input voltage range (VAC): 10.8 - 17.5. Input frequency: 60Hz. Integral surge protector built into LED driver circuit. 12 volts, 12.4 total watts. 12 Volt fixture is pre-wired with 3-ft pigtail of 18-2 AWG, 105° C, SPT-1 wire. Low voltage quick connector, catalog #LVC3 included for easy hook-up to the low voltage supply cable, not included. 12 Volt system requires remote transformer, not included.

Warranty: Three-year limited warranty.

Certification: UL Listed to U.S. safety standards for wet locations. cUL Listed to Canadian safety standards for wet locations. Manufactured to ISO 9001:2000 Standards.

IP Rating: IP66: Dust-tight and sealed against direct jets of water.
Height: 2 3/8" (60mm)
Width: 2 13/16" (71mm)
Length: 5 13/16" (147mm)
Max. Weight: 2.6 lb.

Finish: A Black, H Bronze

Hadco LED Pathlyte (CL2D2)

CL2D2-A LED Contemporary Pathlight
CL2D2-H LED Contemporary Pathlight

Housing: Die-cast aluminum. Gasketed twist lock top. Stem is extruded aluminum. 1/2 " NPS male threads to screw on to accessory mounting stake or junction box, sold separately.

Finish: Thermoset polyester powdercoat is electrostatically applied after a five-stage conversion cleaning process and bonded by heat fusion thermosetting. Laboratory tested for superior weatherability and fade resistance in accordance with ASTM B-117-64 and ANSI/ASTM G53-77 specifications.

Optical Assembly: Clear tempered flat glass lens.

Lamping: Type 3 Luxeon® high-output LEDs powered at 700mA to operate for 50,000 hours.

Electrical Assembly: Input voltage range (VAC): 10.8 - 17.5. Input frequency: 60Hz. Integral surge protector built into LED driver circuit. 12 volts, 6.2 total watts. 12 Volt fixture is pre-wired with 3-ft pigtail of 18-2 AWG, 105° C, SPT-1 wire. Low voltage quick connector, catalog #LVC3 included for easy hook-up to the low voltage supply cable, not included. 12 Volt system requires remote transformer, not included.

Warranty: Three-year limited warranty.

Certification: UL Listed to U.S. safety standards for wet locations. cUL Listed to Canadian safety standards for wet locations. Manufactured to ISO 9001:2000 Standards.

IP Rating: IP66: Dust-tight and sealed against direct jets of water.
Height: 21" (533mm)
Width: 4 3/4" (121mm)
Max. Weight: 2.5 lb.

Finish: A Black, H Bronze

Hadco LED Pathlyte (RL4D3)

RL4D3-A LED Horizon Pathlight

Housing: Die-cast aluminum. Stem is extruded aluminum. 1/2 " NPS male threads to screw on to accessory mounting stake or junction box, sold separately. Fasteners are 300 series stainless steel. Gasketing is silicone.

Finish: Thermoset polyester powdercoat is electrostatically applied after a five-stage conversion cleaning process and bonded by heat fusion thermosetting. Laboratory tested for superior weatherability and fade resistance in accordance with ASTM B-117-64 and ANSI/ASTM G53-77 specifications.

Optical Assembly: Frosted tempered glass lens . Spun aluminum reflector with white thermoset powdercoat.

Lamping: Type 3 Luxeon® high-output LEDs powered at 700mA to operate for 50,000 hours.

Electrical Assembly: Input voltage range (VAC): 10.8 - 17.5. Input frequency: 60Hz. Integral surge protector built into LED driver circuit. 12 volts, 12.4 total watts. 12 Volt fixture is pre-wired with 3-ft pigtail of 18-2 AWG, 105° C, SPT-1 wire. Low voltage quick connector, catalog #LVC3 included for easy hook-up to the low voltage supply cable, not included. 12 Volt system requires remote transformer, not included.

Warranty: Three-year limited warranty.

Certification: UL Listed to U.S. safety standards for wet locations. cUL Listed to Canadian safety standards for wet locations. Manufactured to ISO 9001:2000 Standards.

IP Rating: IP55: Dust-protected and sealed against water jets.

Height: 17 1/4" (435mm)
Width: 10" (253mm)
Max. Weight: 3.18 lb.

Finish: A Black

Hadco LED Pathlyte (ML4D3)

ML4D3-A LED Mushroom
ML4D3-G LED Mushroom
ML4D3-H LED Mushroom

IP Rating: IP66: Dust-tight and sealed against direct jets of water.

Housing: Die-cast aluminum. Stem is extruded aluminum. 1/2 " NPS male threads to screw on to accessory mounting stake or junction box, sold separately. Fasteners are 300 series stainless steel.

Finish: Thermoset polyester powdercoat is electrostatically applied after a five-stage conversion cleaning process and bonded by heat fusion thermosetting. Laboratory tested for superior weatherability and fade resistance in accordance with ASTM B-117-64 and ANSI/ASTM G53-77 specifications.

Optical Assembly: Sealed collimating optics with diffuser lens for even light distribution.

Lamping: Type 3 Luxeon® high-output LEDs powered at 700mA to operate for 50,000 hours.

Electrical Assembly: Input voltage range (VAC): 10.8 - 17.5. Input frequency: 60Hz. Integral surge protector built into LED driver circuit. 12 volts, 9.3 total watts. 12 Volt fixture is pre-wired with 3-ft pigtail of 18-2 AWG, 105° C, SPT-1 wire. Low voltage quick connector, catalog #LVC3 included for easy hook-up to the low voltage supply cable, not included. 12 Volt system requires remote transformer, not included.

Warranty: Three-year limited warranty.

Certification: UL Listed to U.S. safety standards for wet locations. cUL Listed to Canadian safety standards for wet locations. Manufactured to ISO 9001:2000 Standards.

Height: 19 1/2" (495mm)
Width: 5 1/16" (129mm)
Max. Weight: 1.9 lb.

Finish: A Black, H Bronze, G Verde