Hadco I3 Composite Inground Lighting

I3G-H Bronze with Guard
I3-H Bronze

• 120 Volt
• 100 watt maximum
• PAR/R30 & PAR38 Lamps

Housing– Single-piece compression molded fiberglass
reinforced polyester composite housing, lens ring and rock
guard with stainless steel fasteners.

Finish– Color impregnated bronze composite.

Lens– Convex lens is clear, high temperature tempered glass
furnished with silicone molded gasket for watertight seal.

Socket– Porcelain medium base.

Wiring– Pre-wired with high temperature #18 wire.

Aiming– Lamps have 358° rotation and 15° off vertical
adjustability.

UL, cUL Listed.

Hadco LED Inground ILN5D4 & ILW5D4 Spot or Flood Landscape Lighting

ILN5D4-H LED Ultem Inground - Spot
ILW5D4-H LED Ultem Inground - Flood

Housing: One-piece injection molded ULTEM® High Performance Polymer composite. Lens ring is a Single-piece injection molded ULTEM® High Performance Polymer with gasketed lens. Twist-off operation for ease of maintenance. Fasteners are 300 series stainless steel.

Finish: Composite is textured, pressure formed, molded-in-color.

Height: 4 3/8" (111mm)
Width: 4 1/8" (105mm)
Max. Weight: 1.24 lb.

Hadco ILN5D4 & ILW5D4

Optical Assembly: Integral collimating flood (25°) optics. Clear convex lens, high temperature glass furnished with silicone O-ring for watertight seal.

Lamping: Type 3 Luxeon® high-output LEDs powered at 700mA to operate for 50, 000 hours.

Electrical Assembly: Input voltage range (VAC): 10.8 - 17.5. Input frequency: 60Hz. Integral surge protector built into LED driver circuit. 12 volts, 12.4 total watts. 12 Volt fixture is pre-wired with 3-ft pigtail of 18-2 AWG, 105° C, SPT-1 wire. Low voltage quick connector, catalog #LVC3 included for easy hook-up to the low voltage supply cable, not included. 12 Volt system requires remote transformer, not included.

Warranty: Three-year limited warranty.

Certification: UL Listed to U.S. safety standards for wet locations. cUL Listed to Canadian safety standards for wet locations. Manufactured to ISO 9001:2000 Standards.

IP Rating: IP66/68 to 1M (3.28FT): Dust-tight and dual rated - sealed against direct jets of water and against continuous immersion up to a depth of 1 meter (3.28 feet).

Finish: H Bronze

H= Bronze

1/2" N.P.S. conduit inlets on bottom.

Hadco I2 Composite Inground Light

I2G-H Bronze with Guard
I2-H Bronze

• 120 Volt
• 100 watt maximum
• PAR/R30 or PAR/R20 Lamp

IM2G-h20 Bronze

• 120 Volt
• With rock guard
• Mercury Vapor
• 50 MV watt maximum
• HR20 Lamp

Housing– Single-piece compression molded fiberglass reinforced polyester composite housing, lens ring and rock guard with stainless steel fasteners.

Finish– Color impregnated bronze composite.

Lens– Convex lens is clear, high temperature tempered glass furnished with silicone molded gasket for watertight seal.

Socket– Porcelain medium base.

Wiring– Pre-wired with high temperature #18 wire.

Ballast– IM2 standard 120 volt core and coil HPF.

UL, cUL Listed.

Hadco I4 Composite 120 Volt Inground Landscape Light

I4G-H Bronze with Guard
I4-H Bronze

• 120 Volt
• 150 watt maximum
• PAR38/R40 Lamp

Housing– Single-piece compression molded fiberglass reinforced polyester composite housing, lens ring and rock guard with stainless steel fasteners.

Finish– Color impregnated bronze composite.

Lens– Convex lens is clear, high temperature tempered glass furnished with silicone molded gasket for watertight seal.

Socket– Porcelain medium base.

Wiring– Pre-wired with high temperature #18 wire.

Aiming– Lamps have 358° rotation and 15° off vertical adjustability.

UL, cUL Listed.

Inground Installation

1. Excavate soil for fixture placement and conduit runs. Allow a minimum of 3" around and under housing for drainage material.

2. Remove the screws from the glass/gasket assembly and wiring compartment cover. Connect conduit fittings to housing conduit entries utilizing a thread sealant, and tighten to 40 ft-lbs. max. DO NOT REMOVE the moisture absorbing desi-pak from inside the fixture.

3. Connect 120V leads in wiring compartment to supply wires. Make ground connection. The contractor must pull ground wire or make a ground connection to the metal conduit system.

4. Conduit entries must be potted to prevent water entry (3M 4442 GELA supplied with I3 and I4). Replace the wiring compartment cover.

5. Install the ballast tray. Plug lamping module into quick connect, if applicable.

6. Install the correct lamp. DO NOT EXCEED the maximum wattage marked on the fixture.

7. Clean gasket seating surfaces. Screw holes can be blown clear or cleared with a #10-24 tap. Insert screws through lid and tighten using an alternating torque sequence to 20 (min.) 30 (max.) inch-lbs.

8. Fixture housing should be surrounded by a 3" (minimum) layer of sand or gravel to ensure drainage. Materials such as vermiculite and bark are for ground cover only. Full depths of these may cause overheating. In concrete pour cases, the housing is placed on a 4" (minimum) bed of gravel, with soil below. Do not install fixtures where water collects arid stands for any Length of time.

finishes and Materials

Hadco makes it easier than ever to select the right color for your exquisite landscape
design with a full palette of colors and textures. Expand your design capabilities with new finishes that are sure to compliment your commercial or residential landscape lighting needs.

For an aged appearance, Oiled and Verde Brass materials have been added to the NightLife fixture choices for a step back in time.

And for more earthy settings, there is the Speckled Stone finish, which is at home among foliage as well as any number of masonry materials.