WAC Lighting 2.5" Low Voltage Recessed Downlighting

WAC Lighting HR-834 2.5" Metal Trim Ring with Step Baffle

WAC Lighting HR-834 2.5" Metal Trim Ring with Step Baffle on Amazon

2.5 Inch Low Voltage Recessed Downlights 834
Metal Trim with Step Baffle
Superb performance packed into a small package, 3-inch Low Voltage Recessed Downlights offer crisp white beams of light for under cabinet and tight spaces where miniature apertures are required. Beveled round die-cast trim for use with HR-800 series low voltage miniature housings.

• Accomodates most LED MR16 or Halogen MR16 lamps
• Die-cast aluminum construction
• Retention clips secure lens firmly to lamp
• Abrasion resistant powder coat paint or plated metal finish
• Wide range of trim colors and designs
• Smallest general trim available for both commercial and residential lighting projects
• Clear lens included, replaceable lens options available

Finish-Trim: WT-Black/White, WT/WT-White/White
MR16, 35W max HR-800, HR-806
MR16, 50W max HR-801, HR-802

• Accommodates most LED MR16 or Halogen MR16 lamps
• Retention clips secure lens firmly to lamp
• 1W minimum load transformers
• Abrasion resistant powder coat paint or plated metal finish
• Clear lens included, see opposite page for replaceable lens options
• Suitable for damp locations.
• 5 year WAC Lighting product warranty

Construction: Powder coated or plated brushed nickel finish on die-cast aluminum. Inner die-cast aluminum trim body has three retention clips to firmly hold trim to housing. Tension spring holds lens firmly against the lamp.
Accommodates most LED MR16 or Halogen MR16 lamps
Standards: UL & CUL Listed.
Housings: Non-IC housings require 3" of clearance from insulation on all sides. Accommodates ceiling thickness of up to.75" for remodel &.75" for new construction.

WAC Lighting HR-836 2.5" Metal Trim Ring

2.5 Inch Low Voltage Recessed Downlights 836
Metal Trim
Superb performance packed into a small package, 3-inch Low Voltage Recessed Downlights offer crisp white beams of light for under cabinet and tight spaces where miniature apertures are required. Smooth round die-cast trim for use with HR-800 series low voltage housings.

• Accomodates most LED MR16 or Halogen MR16 lamps
• Die-cast aluminum construction
• Retention clips secure lens firmly to lamp
• Abrasion resistant powder coat paint or plated metal finish
• Wide range of trim colors and designs
• Smallest general trim available for both commercial and residential lighting projects
• Clear lens included, replaceable lens options available

Finish-Trim: BN-Brushed Nickel, CB-Copper Bronze, WT-White
MR16, 35W max HR-800, HR-806
MR16, 50W max HR-801, HR-802

• Accommodates most LED MR16 or Halogen MR16 lamps
• Retention clips secure lens firmly to lamp
• 1W minimum load transformers
• Abrasion resistant powder coat paint or plated metal finish
• Clear lens included, see opposite page for replaceable lens options
• Suitable for damp locations.
• 5 year WAC Lighting product warranty

Construction: Powder coated or plated brushed nickel finish on die-cast aluminum. Inner die-cast aluminum trim body has three retention clips to firmly hold trim to housing. Tension spring holds lens firmly against the lamp.
Accommodates most LED MR16 or Halogen MR16 lamps Finish: Brushed Nickel (BN), Copper Bronze (CB), and White (WT) available.
Standards: UL & CUL Listed.
Housings: Non-IC housings require 3" of clearance from insulation on all sides. Accommodates ceiling thickness of up to.75" for remodel &.75" for new construction.

WAC Lighting HR-837 2.5" Round Miniature Directional Spot

2.5 Inch Low Voltage Recessed Downlights 837
Gimbal Ring - 25° Adjustment From Vertical
Superb performance packed into a small package, 3-inch Low Voltage Recessed Downlights offer crisp white beams of light for under cabinet and tight spaces where miniature apertures are required.

• Accomodates most LED MR16 or Halogen MR16 lamps
• Die-cast aluminum construction
• Retention clips secure lens firmly to lamp
• Abrasion resistant powder coat paint or plated metal finish
• Wide range of trim colors and designs
• Smallest general trim available for both commercial and residential lighting projects
• Clear lens included, replaceable lens options available

Finish-Trim: BK-Black, BN-Brushed Nickel, CB-Copper Bronze, CH-Chrome, WT-White
MR16, 35W max HR-800, HR-806
MR16, 50W max HR-801, HR-802

• Accommodates most LED MR16 or Halogen MR16 lamps
• Retention clips secure lens firmly to lamp
• 1W minimum load transformers
• Abrasion resistant powder coat paint or plated metal finish
• Clear lens included, see opposite page for replaceable lens options
• Suitable for damp locations.
• 5 year WAC Lighting product warranty

Construction: Powder coated or plated brushed nickel finish on die-cast aluminum. Inner die-cast aluminum trim body has three retention clips to firmly hold trim to housing. Tension spring holds lens firmly against the lamp.
Accommodates most LED MR16 or Halogen MR16 lamps Standards: UL & CUL Listed.
Housings: Non-IC housings require 3" of clearance from insulation on all sides. Accommodates ceiling thickness of up to.75" for remodel &.75" for new construction.

WAC Lighting HR-800 2.5" Low Profile Housing for use with Remote Transformer for Under Cabinet Application

2.5 Inch Low Voltage Recessed Downlights 800 Non-IC Remodel Housing
Superb performance packed into a small package, 3-inch Low Voltage Recessed Downlights offer crisp white beams of light for under cabinet and tight spaces where miniature apertures are required. Low voltage housing for wood cabinets, displays, and similar wooden applications. Miniature's utilize MR16 lamps, up to 35W maximum, and require a remote transformer.

• Cutout: 3"
• For cabinet use only
• Remote Electronic Class II Transformer required
• 3" clearance on all sides when insulation is present
• Total depth of 4", one of the lowest profile recessed units available
• Low profile housing
• Handles mounting surfaces up to.75" thick
• UL and CUL Listed

Trims: HR-833,HR-834,HR-836,HR-837

• Cutout: 3"
• For cabinet use only
• Remote Electronic Class II Transformer required
• 3" clearance on all sides when insulation is present
• Total depth of 4", one of the lowest profile recessed units available
• Low profile housing
• Handles mounting surfaces up to.75" thick
• UL and CUL Listed

Construction: Housing is 20 gauge galvanized steel, painted black. Electrical components within the can are a bi-pin ceramic socket with nickel plating and 18 gauge teflon insulated wires with fiberglass sleeves.
J-Box: Three ½" knockouts provided for wire entry and exit.
Suitable for chain wiring.
Transformer: Remote electronic class II transformer, sold separately.
Transformer may be 12V or 24V.
Mounting: No screws, nails or hardware required. Flat "wing" springs expand against the cut out hole to hold fixture against the surface.
3" cutout hole. Handles mounting surface thickness up to ¾".
Rating: Non-IC: insulation must be kept at least 3" away from the housing.
Standards: UL & CUL Listed

WAC Transformers & Accessories >

WAC Lighting HR-801 2.5" Remodel Housing equipped with Electronic Transformer

2.5 Inch Low Voltage Recessed Downlights 801 Electronic Non-IC Remodel Housing
Superb performance packed into a small package, 3-inch Low Voltage Recessed Downlights offer crisp white beams of light for under cabinet and tight spaces where miniature apertures are required. 120V input, non-IC remodel housing with electronic transformer.
For use with 2.5" low voltage trims.

• Integral Electronic Transformer
• Advanced auto-reset, soft start and short circuit protection
• 3" clearance on all sides when insulation is present
• Suitable for chain wiring
• J-box and transformer accessible through ceiling opening
• Suitable for damp locations
• UL and CUL Listed

Trims: HR-833,HR-834,HR-836,HR-837

• Integral Electronic Transformer
• Advanced auto-reset, soft start and short circuit protection
• 3" clearance on all sides when insulation is present
• Suitable for chain wiring
• J-box and transformer accessible through ceiling opening
• Suitable for damp locations
• UL and CUL Listed

Construction: Housing is 20 gauge galvanized steel, painted black. Electrical components within the can are a bi-pin ceramic socket with nickel plating and 18 gauge teflon insulated wires with fiberglass sleeves.
J-Box: Three ½" knockouts provided for wire entry and exit.
Suitable for chain wiring.
Transformer: Electronic transformer for 12V MR16 lamps, 50W maximum. 120V input transformer, 1W minimum load.
Mounting: No screws, nails or hardware required. Flat "wing" springs expand against the cut out hole to hold fixture against the surface.
3" cutout hole. Handles mounting surface thickness up to ¾".
Rating: Non-IC: insulation must be kept at least 3" away from the housing.
Standards: UL & CUL Listed

WAC Lighting HR-802 2.5" New Construction Housing equipped with Electronic Transformer

2.5 Inch Low Voltage Recessed Downlights 802 Electronic Non-IC New Construction Housing
Superb performance packed into a small package, 3-inch Low Voltage Recessed Downlights offer crisp white beams of light for under cabinet and tight spaces where miniature apertures are required. 120V input, non-IC new construction housing with electronic transformer. For use with 2.5" low voltage trims.

• Cutout: 3"
• Integral Electronic Transformer
• Advanced auto-reset, soft start and short circuit protection
• 3" clearance on all sides when insulation is present
• Suitable for chain wiring
• J-box and transformer accessible through ceiling opening
• Suitable for damp locations
• UL and CUL Listed

Trims: HR-833,HR-834,HR-836,HR-837

• Cutout: 3"
• Integral Electronic Transformer
• Advanced auto-reset, soft start and short circuit protection
• 3" clearance on all sides when insulation is present
• Suitable for chain wiring
• J-box and transformer accessible through ceiling opening
• Suitable for damp locations
• UL and CUL Listed

Construction: Housing and junction box are 20 gauge steel, painted black. Frame and hanger bars are heavy gauge galvanized steel. Electrical component within can is a bi-pin ceramic socket with 18 gauge teflon insulated wires with fiberglass sleeves.
J-Box: Three ½" knockouts provided for wire entry and exit.
Suitable for chain wiring.
Transformer: Electronic transformer for 12V MR16 lamps, 50W maximum. 120V input transformer, 1W minimum load.
Mounting: Supplied with hanger bars, adjustable from 12"-24" to accommodate various joist construction and grid sizes. Hanger bars have slots for easy mounting on "T" bars. 3" cutout hole. Handles mounting surface thickness up to ¾".
Rating: Non-IC: insulation must be kept at least 3" away from the housing.
Standards: UL & CUL Listed

WAC Lighting HR-806 2.5" Housing for use with Remote Transformer for Ceiling Application

2.5 Inch Low Voltage Recessed Downlights 806 Non-IC Remodel Housing
Superb performance packed into a small package, 3-inch Low Voltage Recessed Downlights offer crisp white beams of light for under cabinet and tight spaces where miniature apertures are required. Low voltage housing for cabinets, displays, soffit, and similar low profile applications. Miniature's utilize MR16 lamps, up to 35W maximum, and require a remote transformer.

• Remote Electronic or Magnetic Transformer required
• 3" clearance on all sides when insulation is present
• Low profile housing
• Handles mounting surfaces up to.75" thick
• Suitable for use in "shallow" joist installations
• Features integral thermal protector
• UL and CUL Listed

Trims: HR-833,HR-834,HR-836,HR-837

• Remote Electronic or Magnetic Transformer required
• Compact enough to fit in 2x6 joist installations, allowing these to be used in "shallow" applications.
• 3" clearance on all sides when insulation is present
• Low profile housing
• Handles mounting surfaces up to.75" thick
• Suitable for use in "shallow" joist installations
• Features integral thermal protector
• UL and CUL Listed

Construction: Housing is 20 gauge galvanized steel, painted black. Electrical components within the can are a bi-pin ceramic socket with nickel plating and 18 gauge teflon insulated wires with fiberglass sleeves.
J-Box: Three ½" knockouts provided for wire entry and exit.
Suitable for chain wiring.
Transformer: Remote electronic or magnetic transformer, sold separately.
Transformer may be 12V or 24V.
Mounting: No screws, nails or hardware required. Flat "wing" springs expand against the cut out hole to hold fixture against the surface.
3" cutout hole. Handles mounting surface thickness up to ¾".
Rating: Non-IC: insulation must be kept at least 3" away from the housing.
Standards: UL & CUL Listed

WAC Transformers & Accessories >